Site: Beverly Laurel Motor Hotel

If the bearings inside the electric motor on your Swimming Pool Pump are starting to make noise you will have to replace them with new bearings or you can replace the entire motor, but why do that when in a few hours you can replace the bearings for a way lower price then buying a new motor. Plus there is no reason to throw away a good motor when the motor on your Super Pump can just be re-built. If you think about it, rebuilding your pool pump motor instead of replacing it is a ECO-friendly thing that you are doing because you are creating less waste.

You Need To Remove The Pump From The System:

The first thing you will need to do before you can remove the bearings from inside your pool pump is to disconnect the pump from the filter system plumbing. This will make it easier for you to work on the pump. You can disconnect the pool pump from the filter plumbing by loosing the suction side and discharge side unions and then the pump will be able to be moved to a place where you can work on it more comfortably. You will need to turn the union collars counter clockwise to loose them. Most of the time PVC unions will have an open arrow and close arrow on them so you know which way to turn.

It’s Time To Remove The Pump Housing, Diffuser & Pump Impeller:

Depending on what brand of pump you have will depend on how the pump housing separates from the motor. If you have a Hayward in-ground pool pump you most likely will have to remove a set of four bolts behind the pump housing. If you own a Sta-right or Pentair pool pump you will have to loosen a bolt and metal band and then the pump housing and motor will come apart. To find out how your model of pump disassembles be sure to take a look at a parts breakdown diagram if you cannot figure it out yourself. Once you have removed the pump housing you will be able to see the diffuser and you will just want to pull that right off the seal housing. Once the diffuser is removed you will need to remove the pump impeller from the motor shaft. You can do this by holding the rear of the motor shaft while turning the pump impeller counter clockwise with a strap wrench. Once the impeller is removed you will be able to move to the next step which is to disassemble the electric motor and armature.

You Will Next Need To Disassemble The Pump Motor:

Now that the electric motor is no longer attached to the pump housing you will be able to start taking apart the motor so you can replace the bearings inside. Most electric motors on pool pumps will have 4 bolts that hold the two end bells of the motor onto the frame. You will need to take a nut driver and remove these four bolts and then you will need to remove the front and rear motor end bells.

Next You will Remove & Replace The Motor Bearings:

Now that the through bolts and the end bells have been removed you can pull out the motor armature, get out your motor bearing puller and you can now remove the bearings with the puller. You should always change both the front and rear motor bearings at the same time. There is no reason you should only change one bearing. You already have the pump apart so you might as well change both bearings even if just one of the bearings is bad. Once you remove both bearings you will now want to re-install two new bearing on the motor armature. You can either use an arbor press to install the bearings or a bearing installation tool to press the bearings onto the electric motor shaft.

Now You Will Reassemble The Motor & Pump:

By now you should have the new pump bearings on to the motor armature so you will be ready to start putting the motor back together. You will want to slide the motor armature into the motor windings and then you will want to re-install the rear and front motor end bells. Once the armature and then end bells are into place, you can insert the motor through bolts and tighten them up with the nut driver. You will want to turn the bolts clockwise to tighten them. Once the motor is all back together you will want to replace the pump seal and then reattach the pump housing to the electric motor in reverse order that you took it apart.

It’s Now Time To Reconnect & To Test The Rebuilt Pump:

Once you have changed the pump motor bearings, replaced the pump seal and have everything back together you will now be ready to re-install the pump back onto the filter system plumbing. Take your pump over to the filter system and reconnect the suction and the discharge side plumbing unions by turning the union collars counterclockwise and then you will want to snug them down with a big pair of channel locks to make sure they are tight. Once both of the unions are tight you can prime the pool pump with some water and then you should plug the pump in and start it up. If everything was installed and rebuilt right you should have a nice and quite fully operation rebuilt swimming pool pump.

Pentair 011517 WhisperFlo Up-Rated Energy Efficient Pump 1-Horsepower 115/208-230-Volt Almond Review

Pentair 011517 WhisperFlo Up-Rated Energy Efficient Pump 1-Horsepower 115/208-230-Volt Almond Feature

• Oversized strainer basket and volute - industry standard in pool Pump
• Standard and Energy-efficient Square Flange Motors available
• Lower HP's deliver higher performance than industry standard
• Compatible with all cleaning systems, various filters and jet action spas
• Heavy-duty/durable construction is designed for long life

Pentair 011517 WhisperFlo Up-Rated Energy Efficient Pump 1-Horsepower 115/208-230-Volt Almond Overview

WhisperFlo High Performance Pumps , Quiet. Efficient. Durable.

WhisperFlo's innovative hydraulic design moves water more efficiently and more quietly than competitive pumps. Under typical operating conditions, WhisperFlo offers the highest water flow of any high performance pump , yet with the lowest electrical consumption. And, WhisperFlo is designed to be a tireless workhorse. Its engineered thermoplastic housing withstands extreme heat and resists corrosion. The commercial grade motor frame has a rust-proof, stainless steel motor shaft and sealed bearings that never need lubrication. Engineered to provide optimum performance in any size pool or pool and spa combination, WhisperFlo is built to last a lifetime, and, as a result, has become the industry's top seller for years. WhisperFlo costs less to operate, because it uses less horsepower to produce required water flow. Whisper-quiet operation documented in rigorous ETL tests. Oversized strainer basket extends time between cleanings. See-through lid makes inspection fast and easy , engineered polymer remains clear and strong for years. User-friendly Cam and Ramp lid is easy to remove and quickly locks in place with a quarter-turn.

Pentair 011517 WhisperFlo Up-Rated Energy Efficient Pump 1-Horsepower 115/208-230-Volt Almond Specifications

Available at Amazon Check Price Now!

*** Product Information and Prices Stored: Feb 04, 2010 17:25:03

Minn Kota Trolling Motors